Use Free 300-510 Exam Questions that Stimulates Actual EXAM
Get 100% Real 300-510 Free Online Practice Test
Topics of Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
These core topics of 310-510 SPRI practice test listed below are general recommendations for the material that is likely to be used for the examination. However, on any delivery of the test, other similar topics could also appear. The guidelines below can update at any time without notice to better represent the contents of the 310-510 SPRI exam dumps pdf and for clarity purposes.
It is recommended that, where possible, the applicant use these courses and/or other resources to provide background information on the exam objectives. The syllabus for the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) examination is listed below in detail for each section of 300-510 SPRI exam dumps:
- Improving BGP Convergence and Implementing Advanced Operations
- Enable and Optimize PIM-SM
- Scaling BGP in Service Provider Networks
- Implement BGP Route Reflectors
- Implement advanced features to improve convergence in BGP networks
- Implementing Cisco MPLS Traffic Engineering
- Implementing Interdomain IP Multicast
- Describe and compare core multicast concepts
- Implement BGP Security Options
- Implement IPv6 tunneling mechanisms
- Implement enhanced Protocol-Independent Multicast - Sparse Mode (PIM-SM) features
- Implementing IP Multicast Concepts and Technologies
- Implement Route Redistribution
- Implementing Segment Routing
- Implement and verify segment routing technology within an interior gateway protocol
- Implement and verifying the PIM-SM protocol
- Introducing Routing Protocol Tools, Route Maps, and Routing Policy Language
- Implement BGP security options
- Troubleshoot Routing Protocols
- Implementing and Verifying Open Shortest Path First Multiarea Networks
- Configure and Verify Interior Gateway Protocol (IGP) Segment Routing
- Influence BGP Route Selection
- Implement and verify MPLS
- Describing Segment Routing Traffic Engineering (SR-TE)
Cisco 300-510 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
| Topic 9 |
|
Who should take the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
People who wish to explore the power of the dynamic culture of the Cisco Learning Network to jump-start their certification and lifelong learning goals should take this exam. Those who want to get useful tools for IT training for all Cisco certifications should also get this certification. People with prior knowledge of integrating VPN services, including Layer 2, Layer 3, and IPv6, from the service provider are highly recommended to take this exam and get themselves certified from Cisco.
List of the target audience for this exam:
- Channel partners
- Network architects
- Network engineers
- Network supervisors
- Network administrators
- Network managers
NEW QUESTION 89
Drag and Drop Question
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
NEW QUESTION 90
Refer to the exhibit.
A service provider technician is working on a multicast issue for a customer. While checking the multicast table, the technician notices that no flags are present for the (1.1.1.1, 239.1.1.1) entry, yet flags are present for the (1.1.1.1, 232.1.1.1) entry.
Which factor might explain this issue?
- A. Only GLOP is permitted
- B. Only the default SSM range is permitted
- C. Only the administratively scoped range is permitted
- D. Only ASM is permitted
Answer: B
NEW QUESTION 91
Refer to the exhibit.
Refer to the exhibit There is a BGP traffic path issue between Customer-1 and Customer-2 Users from Customer-2 have reported file transfer issues High utilization on the path between both customers causes many packet drops. Which configuration resolves the issue?
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: D
NEW QUESTION 92
Which cost is the default when redistributing routes from BGP to OSPF?
- A. 0
- B. infinite
- C. 1
- D. automatic
Answer: C
NEW QUESTION 93
Refer to the exhibit.
Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?
- A. Configure R3 to use metric-type 1 with a higher metric than R4.
- B. Configure R1 with a static route to the R5 networks and set R5 as the next hop.
- C. Change the metric-type value on R3 to 2.
- D. Reconfigure R1 in Area 0.
Answer: C
NEW QUESTION 94
Refer to the exhibit.
Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)
- A. The two routers have password mismatch issues
- B. The two routers are in different subnets
- C. The two routers have the same network ID
- D. The two routers are in the same area
- E. The two routers are in different areas
Answer: B,E
NEW QUESTION 95
Refer to the exhibit.
Router 1 has established an SR-TE tunnel with router 2. Which statement describes this configuration?
- A. Router 1 and router 2 have a bidirectional tunnel set up with dynamic path selection.
- B. Router 1 has a list of labels used to explicitly lay out a path to router 2.
- C. Router 2 is the head-end tunnel and has explicitly set a path to router 1.
- D. Router 1 is the head-end tunnel and has dynamically chosen a path to router 2.
Answer: D
NEW QUESTION 96
Refer to the exhibit.
P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which action fixes the issue?
- A. Change HMAC-MD5 to MD5
- B. Change HMAC-MD5 to HMAC-SHA1-20
- C. Change HMAC-MD5 to HMAC-SHA1-12
- D. Configure the send and accept lifetime under key 1
Answer: D
NEW QUESTION 97
Refer to the exhibit.
After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?
- A. Router 2 uses router 1 as the next hop for 192.168.0.0/24
- B. Router 2 uses router 3 as the next hop for 192.168.0.0/24
- C. Router 2 receives a Type 5 LSAs from router 1 for its connected subnets
- D. Router 2 receives a Type 7 LSAs from router 3 for its connected subnets
Answer: C
NEW QUESTION 98
You noticed a recent change to the BGP configuration on a PE router, the bgp scan time has been changed from the default value to 30s.
Which three effects will this change have? (Choose three.)
- A. The BGP keepalive messages will be sent to the BGP peers at a faster rate
- B. The BGP table will be modified more quickly in the event that a next-hop address becomes unreachable
- C. The minimum time interval between sending EBGP and IBGP routing updates will decrease
- D. The BGP table will be examined and verified more frequently
- E. The BGP convergence time will increase
- F. The CPU load of the router will increase
Answer: B,D,F
NEW QUESTION 99
Refer to the exhibit.
An engineer applied the configuration on R1 to prevent network 192.168.1.0/24 from being propagated outside of area 5. After the change, users have reported they are not able to access any of the application servers that were working before. While checking the routing table of the peer router. The engineer notices R1 stopped propagating any routes outside are 5. Which action must be taken to fix the problem?
- A. Change the prefix-list action to permit and add an explicit deny statement for network 192.168.1.0/24
- B. Add a permit statement for 0.0.0.0/0 le 32 to the end of the prefix-list 10 override the implicit deny.
- C. Reconfigure the filter-list statement to apply in the inbound direction
- D. Configure an additional filter-list on R1 for inbound traffic to allow external router into area 5.
Answer: B
NEW QUESTION 100
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)
Answer:
Explanation:
NEW QUESTION 101
Refer to the exhibit.
An administrator is troubleshooting Internet access issues on a customer's network. After applying this ISIS configuration to R1, the administrator notices that it fails to redistribute the default route into IS-IS. After checking the connectivity between the ISIS router and the ISP router the engineer confirmed there is Layer 3 connectivity between them Which action should be taken to correct the problem?
- A. Associate the default route with a VRF
- B. Configure the default route under any routing protocol other than IS-IS
- C. Add the default-information originate command to the configuration
- D. Configure R1 as a Layer 1 router
Answer: C
NEW QUESTION 102
Refer to the exhibit.
A network operator is working to deploy a Unified BGP design and allow it to be available only in selected markets and services in the future. The label allocation is not functioning as desired. Which action will fix the issue?
- A. Remove the allocate-labels command.
- B. Remove the route policy and only configure "allocate-label".
- C. Reconfigure the route-policy ALL_LABELS to pass.
- D. Reconfigure the route-policy ALL_LABELS to match all after the drop.
Answer: C
NEW QUESTION 103
Which output from the show isis interface command helps an engineer troubleshoot an IS-IS adjacency problem on a Cisco IOS-XR platform?
- A. priority
- B. hello interval
- C. metric
- D. circuit type
Answer: B
NEW QUESTION 104
For which reason can two BGP peers fail to establish a neighbor relationship?
- A. Their remote-as numbers are misconfigured
- B. They are both activated under an IPv4 address family
- C. Their BGP timers are mismatched
- D. Their BGP send-community strings are misconfigured
Answer: A
NEW QUESTION 105
Refer to the exhibit. An engineer is troubleshooting an OSPF issue.
Router 1 has a neighbor relationship with router 2.
Only router 1 classful EIGRP routes can be seen on router 2.
In order for all EIGRP routes to be redistributed correctly, which action should be taken?
- A. Router 1 must have the keyword subnets included in the redistribution command for all EIGRP routes to be redistributed.
- B. Router 1 must remove the AS number 1 from the redistribution command for all EIGRP routes to be redistributed.
- C. Router 1 must have the keyword ospf-metric included in the redistribution command for all EIGRP routes to be redistributed.
- D. Router 1 must have the keyword metric-type 1 included in the redistribution command for all EIGRP routes to be redistributed.
Answer: A
NEW QUESTION 106
Refer to the exhibit.
After configuring IS-IS on routers R1 and R2, an engineer notices that only the loopback interface at 2000:1::1 /96 is known to router R2. Which change must be made so that only Loopback2 is advertised from R1 to R2?
- A. Remove the ipv6 router isis areal command under the Loopback2 interface on R1.
- B. Remove the advertise passive-only command under the IS-IS address family ipv6 configuration
- C. Configure the router isis areal command under the LoopbackO interface on R1.
- D. Remove the passive-interface Loopback0 command under the router isis areal configuration.
Answer: B
NEW QUESTION 107
Refer to the exhibit.
Which tree does multicast traffic follow?
- A. source tree
- B. MDT default
- C. MDT voice
- D. shared tree
Answer: B
NEW QUESTION 108
Refer to the exhibit. Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3.
Which action corrects the problem?
- A. Configure R3 to use metric-type 1 with a higher metric than R4.
- B. Configure R1 with a static route to the R5 networks and set R5 as the next hop.
- C. Change the metric-type value on R3 to 2.
- D. Reconfigure R1 in Area 0.
Answer: C
NEW QUESTION 109
Refer to the exhibit. Router 1 is connected to router 2 on interface TenGigE0/1.
Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?
- A. A backup path must be statically installed
- B. TenGigE0/2 interface provides the alternate path
- C. TenGigE0/1 interface provides the alternate path
- D. A primary path must be manually installed
Answer: B
NEW QUESTION 110
Refer to the exhibit.
A network operator is getting the route for 10.11.11 0/24 from two upstream providers on
#XR3. The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to route via next hop of
10.0.0.9 as primary when available. Which of these can the operator use the routing policy language for, to enforce this traffic forwarding path?
- A. higher local preference on the prefix coming from 192.168.0.1
- B. weight of 100 on the prefix coming from 192.168.0.1
- C. weight of 0 on the prefix coming from 192.168.0.2
- D. lower local preference on the prefix coming from 192.168.0.2
Answer: C
NEW QUESTION 111
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network. Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)
Answer:
Explanation:
NEW QUESTION 112
......
BEST Verified Cisco 300-510 Exam Questions (2023) : https://examtorrent.actualcollection.com/300-510-exam-questions.html